StageDesigner

DMX addressing: modes, lines, universes and nodes

How the planner splits fixtures into DMX lines, assigns universes and addresses based on fixture modes, when it adds nodes and splitters, and which limits it checks.

4 min read
Documentation contents ▾

You plan DMX in the same wizard as the rest of the cabling: just tick the DMX family. The planner links fixtures into chains, splits them into lines, assigns universes and addresses, and uses the console from the control room, existing nodes or new nodes near the stage as the signal source.

UNIVERSE 1 · node A / line 1298 / 512 ch1128256384512Spot 1 · address 1.001 · extended mode26 ch1Dimmer2Shutter3Pan4Pan fine5Tilt6Tilt fine7Color 18Color 29Gobo 110Gobo 1 rotation11Prism12Focus… 13–26: animation, macros, CTO, iris, reset
DMX lines from nodes to fixtures and addresses in universes.

Channel count from the fixture mode

Each fixture in the app has a list of DMX modes (personalities), and each mode a list of channels in order, with a function and function group. The length of this list is the only source of the channel count: the patch, channel map and report all use the same footprint. The default is the first mode in the list. How to change the mode is described in DMX fixture mode.

Chains and lines

  • Fixtures on the same truss are linked one after another along the runs, starting from the end closer to the source.
  • Fixtures on the floor form clusters (up to 6 m between neighbors) linked by nearest neighbor.
  • Each position (truss, floor cluster) has its own line: a failure of one fixture does not cut off other positions. Floor clusters can share a line when they are within 20 m of each other and fit within the limits.
  • A line has no Y splits. A splitter does the branching, and every line ends with a terminator.
LimitValue in the app
Devices per line32
Line length300 m
Channels per universe512
Line capacity for planning460 channels (10 % headroom)

Universes

In the Rules step, the wizard has the DMX lines setting:

1 line = 1 universe
Default. Each line has its own universe, the next free one starting from 1.
Lines share a universe
Lines share a universe as long as the total channel count fits within the capacity. Physically these are splitter outputs carrying the same universe; the planner adds a DMX Splitter 1 → 4 or 1 → 8.

Fixtures with a manually entered address go on lines of their universe. Universe numbers in the app start at 1 (as in sACN). The line table and channel map also show the Art-Net address, which starts at 0: U1 is 0:0:0, U17 is 0:1:0.

Signal source: console, node, splitter

The planner looks for a source in this order: the lighting console in the control room and Art-Net/sACN nodes in the project. It adds new nodes when the console is more than 30 m from the stage center, when there are more than 2 universes, or more universes than the console has DMX outputs. The node size (2, 4, 8 or 12 outputs) depends on the number of missing outputs. The first one is named "DMX node at stage".

The console connects to the nodes with a network cable (Cat6, or fiber on long runs; when the port is not optical, the planner adds a media converter). Without a console or nodes, the lines start from a point named "Console at stage".

Addresses

Fixtures get addresses in order along the chain. With the readable addresses setting on (yes by default), fixtures of one type get consecutive addresses in a block within the universe, and each type block starts at a full hundred (1, 101, 201…), if it fits. A fixture never goes past channel 512. Manual entries stay and occupy their range.

The same setting has three names depending on where you are: Start at round values in the wizard, Readable addresses in the DMX tab and Start at full hundreds in the channel map.

DMX tab in the Cabling panel

The DMX lines table has the columns: line (D1, D2…), universe, number of devices, channels out of 512, length. Each line has a Split line button. The group description gives the number of terminators and the line limits. The Channel map button opens the DMX map. Below the line table is the patch, described in DMX patch.

The DMX tile at the top of the panel shows the number of universes, lines and used channels out of the universe capacity.

Universes in the console inspector

A lighting console has a DMX Universes section in the inspector: the universes of lines that leave the console directly or through nodes and splitters, a channel usage bar, number of fixtures, lines and the device they come out of. When the catalog knows the console's universe count, the section compares it with the plan. Actions: DMX Channel Map and Plan DMX cabling.

Did not find the answer?
Describe the problem and we will reply with a solution or add an article.