StageDesigner

Structure wizard and templates

How to pick a template in the Structures panel (FOH truss, goalpost, portal, frame, grid, mother grid, ground support, stage roof, circle, truss on stands), set dimensions, support and series, then insert the structure in the view or draw it on the plan.

6 min readStudio plan
Documentation contents ▾

The New structure wizard builds the whole structure as one object: runs made of series sections, corners, towers or rigging points, and hardware. You enter dimensions in meters, and the app splits each run into standard sections by itself and calculates indicative statics right away.

Structures panel (⌘ 5 / Ctrl + 5)New structure
LED screen 520 kg · 4 × spot 36 kg86 %4.1 kN4.1 kN< 70 %70–90 %> 90 %
A structure from the wizard: span utilization colors and support loads.

Templates

The wizard has ten tiles with thumbnails. After you pick a tile, the form shows only the dimensions that make sense for that layout and fills in default values. You can change the default support and cross-section in the Support and series section.

TileUsed forDimensions in the formDefault
FOH trussStraight truss on hoists above the audienceWidth, bottom chord heightHoists, 290 cross-section, Above audience on
GoalpostTruss on two towers with base plates and outriggersWidth, heightTowers, 290 cross-section
PortalFrame on four towersWidth, depth, heightTowers, 290 cross-section
Flown frameRectangle on hoists at the cornersWidth, depth, heightHoists, 290 cross-section
GridRectangle with cross runs every few metersWidth, depth, run spacing, heightHoists, 400 cross-section
Mother gridHeavy load-bearing grid for other structuresWidth, depth, run spacing, heightHoists, 520 cross-section
Ground supportFrame lifted on GS towersWidth, depth, heightGround support, 400 cross-section
Stage roofRoof on GS towers (estimated)Width, depth, heightGround support, 520 cross-section
CircleCircle made of catalog arcsDiameter, heightHoists, 290 cross-section
Truss on standsLight truss on two crank-up standsWidth, heightStands, 290 cross-section

Dimensions and section layout

The Dimensions group contains the fields Width, Depth, Run spacing (grid and mother grid), Diameter (circle) and Bottom chord height. Under each field the wizard shows how the run splits into series sections, including the corner legs, for example "0.5 + 3 + 3 + 3 + 0.5 m (corners 0.5 m)".

When the entered length cannot be built from sections, the row gets the status cannot be built from series sections. Choose below. and the two nearest achievable values as buttons. One click sets a valid dimension.

Bottom chord height
Underside of the truss above the floor. The truss axis sits higher by half the cross-section.
Run spacing
Grid and mother grid: the distance between cross runs. The wizard fits it to the sections and shows the actual dimension if it differs from the value you entered.
Diameter
Circle: catalog diameters from Ø 2 to Ø 12 m. Up to Ø 6 m the circle has 4 arcs, from Ø 8 m it has 8 arcs.
Towers on base plates
The bottom chord height must come from tower sections (base plate, sections, corner). If it does not add up, the wizard offers the two nearest heights.

Support and series

The Support and series section is collapsed. Its summary shows the series, support type and location. When expanded, it offers:

Series
A list of truss series in 290, 400 and 520 cross-sections (square, triangle, ladder) plus the generic series Standard 290, Standard 400, Standard 520. The hint next to each item tells you which load table the series uses; a series without a table is marked no load table.
Support
Hoists, Towers, Stands or Ground support.
Tower base
Towers and GS only: Automatic, Base plate 600 mm, Base plate 800 mm, Base plate with outriggers, GS base.
Location
Indoor or Outdoor. Outdoor turns on wind and ballast calculations.
Above audience
Forces D8+ class hoists at every point.
Cable allowance
Light 1 kg/m, Standard 2 kg/m, Heavy 3.5 kg/m. When the project has a cabling plan, the cables from the plan are used.

Live summary

Under the form, two tiles show the result of the same analysis the inspector uses: the rating (OK, Caution, Overload) with the highest span utilization, and the mass with a description of the supports. If there is a warning, the first one appears in a box under the tiles. The summary recalculates a moment after you stop typing, so typing in the fields does not slow the app down.

Inserting and drawing

  1. Pick a template tile.
  2. Enter the dimensions. If a row shows a status, click one of the suggested values.
  3. Expand Support and series and set the series, support and location.
  4. Check the summary tiles and any warning.
  5. Click Insert in view to place the structure in the center of the view, or Draw on plan to set its position and dimensions with the Draw Truss tool (T).

Draw on plan starts the tool with a shape matching the template: a path for trusses, a rectangle for frames, portals and grids, a circle for the circle. Details in the article Drawing the run and section selection.

Stage roof

The Stage roof template adds an estimated roof mass from a dimension table (the upper bound of the range is used for calculations) and splits the sides into several GS towers by itself if spans or towers would be overloaded with only four corner towers. The structure always gets the note "A stage roof requires system documentation and structural calculations." Treat the roof only as a visualization and a starting point for a conversation with the system supplier.

My presets

You can save a finished structure as a preset in the inspector: the Presets section, the Preset name field, the Save preset button. Presets appear in the Structures panel in the My presets section. Clicking one inserts a copy in the view, the trash icon deletes the preset (you can undo it). Presets are saved locally on the device.

Studio plan

Did not find the answer?
Describe the problem and we will reply with a solution or add an article.