StageDesigner

Drawing the run and section selection

The Draw Truss tool (T): clicking out the run, rectangle and circle, snapping to lengths that can be built from sections, closing the structure, and changing how a run splits into sections in the inspector.

4 min readStudio plan
Documentation contents ▾

When you draw a structure, you only show the run. The app picks standard series sections, corners at the bends and supports according to the selected support mode. It never inserts a single "artificial" section of arbitrary length: a 7 m run is, for example, 4 + 3 m.

ToolsDraw Truss (T)

Drawing a path

  1. Press T or click Draw on plan in the wizard. Series, height and support settings are taken from the New structure wizard.
  2. Click the start point on the floor.
  3. Click the next corners. The status line shows the length of the current run, how it splits into sections and its direction.
  4. Finish with Enter or a double-click.
T
Draw Truss tool
Click
Add point
Double-click / Enter
Finish the structure
Backspace
Undo the last point
Esc
Cancel drawing
Shift+drag
Rectangle (frame or portal depending on the support mode)
O (before the first point)
Circle: click the center, click the radius

Snapping

The run direction snaps every 15°. The length snaps to the nearest length that can be built from series sections (with the corner leg) when the cursor is within 0.15 m of it. Elsewhere a 0.25 m grid applies. Points also snap to the ends, corners and midpoints of other structures in the scene.

Hints appear next to the cursor: Axis continuation, 90°, Parallel and Same length as A1 (with the run number) when the new run has the length of one of the previous ones.

The dot in the status line shows validity: green when everything is built from sections, orange when there are notes, red when there is an error. When a run does not add up, the status line says how much is missing, for example "sections 4 + 3 m (0.25 m missing)". The second line shows the total length, the number of sections and joints, and the indicative mass.

Closing the structure

When the last point lands on the first one, the app asks whether to create a closed structure. The Closed structure detected window also recognizes a typical layout (for example a portal) and offers:

  • Close structure: a loop with automatically selected corners and supports.
  • Close on towers: the same with towers (when the support is not already set to towers).
  • Leave open: the structure ends at the last point.
  • Cancel: you go back to drawing.

How the app selects sections

Each run is split into sections from the series list (from 0.25 to 4 m; the 520 cross-section has no 0.25 m section). When choosing a layout, the app prefers:

  • as few joints as possible,
  • a symmetric layout (for example 10 m as 3 + 4 + 3),
  • short sections at the ends, not in the middle,
  • no joint in the zone of the highest moment, that is in the middle of the span,
  • avoiding 0.25 m sections.

If the length cannot be built, the app does not silently drop the remainder: the run gets the warning "Run … m cannot be built from sections." with a Set … m button for the nearest achievable length.

Changing the layout and length in the inspector

Select the structure and open the Geometry section in the inspector. Tiles show the run length, outline, bottom chord height and the number of sections, corners and joints. The Runs table has a length field and a Sections column for each run (B1, B2…).

  1. Enter a new run length in the table field. The structure recalculates right away.
  2. Click the layout in the Sections column to see other arrangements of the same length, for example "4 + 2 + 4" or a symmetric variant.
  3. When a run does not add up, the same list shows the nearest achievable lengths.
  4. The Add run button extends an open structure; the trash icon deletes a run.

Corners

Corners are created automatically at the nodes. You choose the type in the Structure section, in the Corners field: n-way corners or Box corner. The Corners table in the Geometry section shows which part lands at each node (N1, N2…).

Series have 45°, 60°, 90°, 120° and 135° corners. An angle outside this list gives the note "Angle … not available in the series." with the fixes Align to …° or Use box corner.

Did not find the answer?
Describe the problem and we will reply with a solution or add an article.